MGP WRM2 Spécifications Page 20
- Page / 62
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
15-00044
Revision 5
April 2008
The publication, translation or reproduction, either party or wholly, of this document are not allowed without our written consent. 20
4. General Functions
4.1 Dipswitch Selector
To set the dipswitch, unscrew two screws located at the meter front panel and remove the dipswitch cover.
T
he dipswitch (8 switches) is located on the meter’s front panel. Using these dipswitches you can setup two
functions:
a) Communication mode, and;
b) Connect-disconnect the backup batteries.
Dipswitches position: For the ON position, press the dipswitch downward.
The DRM has one UART (Universal Asynchrony Receive Transmit Port) and one communication RS232 port;
the dipswitch position enables a selection of the communication mode
To set the dipswitch, unscrew two screws located at the meter front panel and remove the dipswitch cover.
4.2 Dipswitch Positions
4.2.1 1&2 On
• C
onnects the DRM UART to the RS232 communication port via the D-type 9 pin female connector
• Enables connection of the meter to PC for meter parameter setting, calibration or download the meter reading
directly to PC, (Using RMV software for configuration and RMC for calibration).
4.2.2 3 On & 4 Off
• Connects the DRM UART to the internal wireless transmitter to send data reading via WRM2. Switch 3 is
for transmitting and Switch 4 is for receiving data.
4.2.3 5&6 On
• Connects the internal wireless transmitter to the RS232 communication port via the D-type 9 pin female
connector. See “Wireless Remote Monitoring 2 Operating manual, 15-00043” for configuring the WRM2
radio.
• Enables the setting of internal wireless transmitter WRM2 parameters.
4.2.4 7&8 On
• C
onnects the internal three NiMHd rechargeable batteries for back-up power if the external power is
disconnected
Note: If the external power supply is connected, the battery will be charged even
though the dip switches 7&8 are in the OFF position.
- DRM Family of 1
- Revision Log 2
- WRM-2 FCC COMPLIANCE 3
- ANTENNA WARNING 3
- Table of Contents 4
- 1. DRM-1/2 and DRM-1D 6
- 1D) Detectors 7
- 2. DRM Specifications 8
- 2.3 DRM-2 Specifications 10
- 15-00044 11
- Revision 5 11
- April 2008 11
- 2.4 DRM Outline Drawings 12
- 3. Operating Instructions 17
- 3.3 Meter Connectors 18
- 3.3.2 External Connectors: 19
- 4. General Functions 20
- Important Note: 21
- 4.2.11 Dose Function 24
- 4.4 Battery Replacement 27
- 5. Communication 28
- 6. Communication Protocol 28
- 6.1.4 Set Dose status = 37H 31
- 6.1.6 Set Baud Rate = 31H 31
- AMP + DRM 32
- 9 54 008 34
- 8.1 Preface 35
- 9.1 Preface 36
- 10.1 Preface 37
- 10.2 Operating Instructions 37
- 10.5 Calibration 41
- 10.6 Linearity 42
- 10.7 Save, Load and Print Ca 44
- New *.hex file 48
- April 2008 52
- April 2008 53
- 14. DRM Solar Configuration 57
- DRM1/DRM1D 61
- Alarm Display 62
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité MGP WRM2
(40 pages)Adata Cyfrowe rejestratory wideo (DVR) podręczniki użytkownika
Lista Adata Cyfrowe rejestratory wideo (DVR) produkty zawierają 1 instrukcje obsługi do modeli 1. Wszystkie podręczniki użytkownika w formacie pdf są dostępne do pobrania lub obejrzenia online.
Commentaires sur ces manuels